All Zephyrtronics Equipment is Engineered and Manufactured in the United States of America.
The Prestigious
"Vision Award" Presented to Zephyrtronics at the Surface
Mount Int'l Expo in Silicon Valley Recognizing Its
Breakthrough Approach For PCB's at the Bench!
"Innovative...simpler, safer
way to remove and repair sensitive devices" --
The Editorial Staff of
SMT MAGAZINE
The
Zephyrtronics
AirBath is Featured
in Ray Prasad's Definitive Text "Surface Mount
Technology"
NASA
Publishes 39-Page Report Touting Zephyrtronics With Over
300 Photographs After the Successful Mars Rover Program
Video Demonstrations & PresentationsThe Best Solution for SMD, SMT, BGA Rework and Repair and PCB Preheating
How to Solder & De-Solder & Preheat BGA's, SMD's, QFN's & More.
Video: ABC Board Holder's Key
Advantages
This helpful, comparative video
details the many advantages, utilities and
unparalleled versatility of our
ABC Series of Adjustable
Board Cradles over all other PC
Board fixtures and holders.
This fun, truth-telling video pulls no
punches and demonstrates the serious pitfalls
and limitations of other inferior approaches and
how they actually punish the PCB technician,
waste time (money) and hurt productivity at the
benchtop during PCB prototyping, rework and
repair.
The short video spotlights
the eyebrow-raising and uncanny
multiple functions and utilities that made
the ABC Series the most popular PC board
fixtures on the planet for twenty years.
There's a lot more than just meets the eye when
it comes to the amazing and transforming ABC
Adjustable Board Cradles. Check out the video.
You'll be impressed.
Video Duration: 4 quick minutes.
RELATED VIDEOS:
Video: BGA DeSoldering & Removal
Demonstration With NASA Commentary
This short, but informative video demonstrates quality
and ease of soldering, desoldering, and BGA removal in
less than 5 minutes. Thermal profiling is taught with
ramp, preheat, soak and final solder reflow, plus
removal of a BGA, QFN, CSP or any SMD device.
Video shows board prep, fluxing, chip
alignment, soldering, desoldering & PCB clean-up after
chip removal. The video shows quality PCB inspection
after desoldering a BGA as it actually lifts
off the PCB...hands-free! Photo and observations from
NASA are included in the video. Afterward visit
our
ZT-7 WebPage
for more details. 10 minutes.
Importance of ramping, preparing the
PCB, applying solder paste, hot air
reflow of the SMD, clean-up &
inspection. See how easy using solder
paste instead of solder wire is. All
equipment, tools and supplies shown in
video are included in any of our popular
Zephyrtronics Systems.
Video: 5 minutes.
Video:
Remove SMD Chips Quick @ 150°CThis short video demonstrates
how to de-solder and remove SMD's in
less than 3 minutes through the synergy of
LowMelt®
Desolder &
AirBath Preheaters.
Technicians can confidently remove SMT chip (QFP's, PLCC's, SOIC's SOL's SOJ's
&
sockets) without specialty
nozzles at below 150°C!
Learn how to remove any chip
quickly without burning boards, lifting
pads or chip damage. through the Science
of Zephyrtronics™ now utilized daily by
NASA, Motorola, Hewlett-Packard and the
Department of Defense. For more details,
see our
Systems Guide.
Video: 5 minutes.
Video: The Science
of Low Temperature Soldering & De-Soldering:
This video
teaches how to place, remove, rework
and repair SMD's and Thru-Hole Devices
including ceramic capacitors, glass diodes, flex
circuits and resistors without damage to the substrate,
its pads, traces or the chips...when the "science" is on
your side!
Using animation and charts, the video
teaches the three critical thermal zones that
encompass most PCB's during production and how
these same 3 zones apply to PCB's at a bench in
prototyping, rework and repair.
After the video,
visit our
Systems Guidefor more details. Duration: 9 minutes.
Video:
The 4 PCB Preheat Methods. This comparative video juxtaposes the 4 current
methods of preheating PCB's spotlighting their
drawbacks and advantages. The viewer sees use of
hot plates, infrared (IR) preheating, industrial
ovens and the popular bottom-side forced
convection (AirBaths™)
along with comparative charts and graphs.
The video clearly demonstrates why
bottom-side, forced convection method became the first choice of electronic
manufacturers around the globe, why it is more effective and better suited
to PCB prototyping, rework and low volume production runs
when soldering & desoldering SMD, BGA, QFN & Thru-Hole
chips. Duration: 9
minutes.
